Jan 12, 2024 Leave a message

UNS N08810 Nickel-Iron-Chromium Alloy: Composition and Standards

What UNS N08810 Is

UNS N08810 is a nickel-iron-chromium alloy with a controlled carbon content of 0.05 to 0.10 percent and an intentional coarse grain size. It belongs to the same 20/32 family of alloys as UNS N08800, but the higher carbon level and the high-temperature anneal are what allow it to be used above 600 degrees Celsius, where creep and rupture strength rather than short-term tensile strength govern the design.

The alloy combines good mechanical properties with resistance to oxidation, carburisation and many corrosive media, and it is readily welded. Those characteristics suit it to superheater and reheater tubing, high-temperature heating elements, and conversion and cracking furnace tubes in the chemical, electric power and petrochemical industries.

Composition and Physical Properties

Carbon content is the defining feature of the grade, and the aluminium and titanium additions at a minimum level of about 0.15 percent each support the protective oxide scale.

Element Requirement
Carbon, C 0.05-0.10 percent
Silicon, Si 1.00 percent maximum
Manganese, Mn 1.50 percent maximum
Chromium, Cr 19.0-23.0 percent
Nickel, Ni 30.0-35.0 percent
Aluminium, Al 0.15-0.60 percent
Titanium, Ti 0.15-0.60 percent
Copper, Cu 0.75 percent maximum
Phosphorus, P 0.045 percent maximum
Sulphur, S 0.015 percent maximum
Iron, Fe balance
Property Value
Density 8.0 g/cm3
Melting range 1350-1400 degrees Celsius
Specific heat capacity about 500 J/kg.K
Electrical resistivity at room temperature about 0.99 micro-ohm.metre
Elastic modulus at room temperature about 196 GPa

A frequently copied table lists the elastic modulus of this alloy as 200 MPa. That figure is a unit error; the modulus is of the order of 196 GPa, which is roughly 196000 MPa.

Product Standards and Heat Treatment

Each product form has its own specification, and the ASME equivalents carry the same numbers with the SB prefix.

Product form Specification
Plate, sheet and strip ASTM B409
Seamless pipe and tube ASTM B407
Welded pipe ASTM B514
Welded tube ASTM B515
Rod, bar and forging stock ASTM B408
Fittings ASTM B366

Thermomechanical processing follows established windows:

Hot working: 900-1200 degrees Celsius; hot bending is carried out at 1000-1150 degrees Celsius.

Final anneal: 1120-1170 degrees Celsius followed by rapid cooling, normally a water quench, to keep the carbon in solution and to develop the coarse grain size that the grade depends on.

Sensitisation window: pass through 540-760 degrees Celsius as quickly as possible during processing, because holding in that range promotes chromium carbide precipitation at the grain boundaries.

Cold working: intermediate softening anneals are required, and the finished part is normally given the full solution anneal before service.

Corrosion, Welding and Applications

The alloy resists nitric acid, organic acids such as formic and acetic acid, and oxidising and non-oxidising salts, with the notable exception of halide salts. Its high-temperature corrosion performance is good: it resists oxidation and carburisation, and shows useful resistance to steam and to steam, air and carbon dioxide mixtures. Intergranular corrosion can occur if the material is held between 540 and 760 degrees Celsius, and long-term ageing around 650 degrees Celsius changes the stress corrosion behaviour. Resistance in sodium hydroxide and in chloride solutions depends on concentration and temperature, and it should be confirmed against the actual service conditions rather than assumed.

Performance in seawater is a useful example of the same caution. The alloy resists flowing seawater well, but in stagnant seawater deposits form on the surface and can lead to crevice attack, so drainage and velocity need to be part of the design.

Welding is straightforward with conventional processes, and matching filler metal is normally used. The joint area should not be held in the sensitisation range, and post-weld heat treatment is generally not required for section thicknesses used in tube and sheet products.

Typical applications include superheater and reheater tubing, high-temperature heating elements and furnace internals, conversion and cracking furnace tubes, and heat exchanger tubing in the chemical, electric power and petrochemical industries.

Equivalent designations appear in several national systems: NS1102 and 0Cr21Ni32AlTi in Chinese catalogues, 1.4958 and X5NiCrAlTi31-20 in European catalogues, and the grade is also written loosely as No8810. Because look-alike designations circulate in the market, the purchase order should always carry the UNS number N08810 together with the product specification, so that the correct carbon level and grain size are received.

Frequently Asked Questions

Q: What is UNS N08810?
It is a nickel-iron-chromium alloy with 30 to 35 percent nickel, 19 to 23 percent chromium and a controlled carbon content of 0.05 to 0.10 percent, intended for service above 600 degrees Celsius.

Q: What is the difference between UNS N08810 and UNS N08800?
They belong to the same alloy family, but N08810 has a higher carbon content of 0.05 to 0.10 percent and receives a high-temperature anneal that produces a coarse grain size, which raises creep and rupture strength at high temperature.

Q: Which standards cover UNS N08810?
ASTM B409 for plate, sheet and strip, ASTM B407 for seamless pipe and tube, ASTM B514 for welded pipe, ASTM B515 for welded tube, ASTM B408 for rod and bar, and ASTM B366 for fittings.

Q: How is UNS N08810 heat treated?
It is annealed at 1120-1170 degrees Celsius and rapidly cooled, usually by water quenching, after hot working at 900-1200 degrees Celsius.

Q: What temperature range should be avoided during processing?
The 540-760 degrees Celsius sensitisation range. Parts should pass through it quickly to limit chromium carbide precipitation at the grain boundaries and the associated risk of intergranular corrosion.

Q: Where is UNS N08810 used?
In superheater and reheater tubing, high-temperature heating elements and furnace internals, and conversion and cracking furnace tubes in chemical, electric power and petrochemical plants.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry