ASTM B444 UNS N06625 Seamless U-Tube for Heat Exchangers

What ASTM B444 Seamless U-Tubes Are

ASTM B444 covers cold-worked seamless pipe and tube produced from the nickel-chromium-molybdenum-niobium alloy UNS N06625, equivalent to WERKSTOFF NR. 2.4856. A seamless U-tube is made by bending a straight seamless tube to a controlled bend radius so that one tube passes through a heat exchanger shell twice. That geometry doubles the effective heat-transfer surface inside a compact bundle and removes two longitudinal weld seams and two tube-to-tubesheet joints from the pressure boundary.

The alloy is a single-phase austenitic material strengthened by the solid-solution effect of molybdenum and niobium in the nickel-chromium matrix. Because no precipitation-hardening step is required, the tube keeps its corrosion resistance and toughness from the mill condition through to service, and it retains useful strength up to roughly 816 °C (1520 °F).

Grade 1 and Grade 2 Heat Treatment

ASTM B444 splits the alloy into two grades that differ only in the final thermal treatment applied by the mill. The definitions are sometimes reversed in secondary sources, so the ordering code should name the grade rather than rely on the generic word annealed.

Grade Condition supplied Typical use
Grade 1 Annealed Maximum formability for tight U-bends and cold working
Grade 2 Solution treated Higher minimum mechanical properties in service

Both grades are covered by ASME SB444 for pressure-retaining service and can be supplied with U-bend, plain or beveled ends.

Chemical Composition of UNS N06625

Element Requirement, %
Nickel (Ni) 58.0 min
Chromium (Cr) 20.0 – 23.0
Molybdenum (Mo) 8.0 – 10.0
Niobium plus tantalum (Nb + Ta) 3.15 – 4.15
Iron (Fe) 5.0 max
Carbon (C) 0.10 max
Manganese (Mn) 0.50 max
Silicon (Si) 0.50 max
Aluminium (Al) 0.40 max
Titanium (Ti) 0.40 max
Sulphur (S) 0.015 max
Phosphorus (P) 0.015 max

Aluminium and titanium each carry their own separate maximum; they are not combined into a single limit. The niobium plus tantalum range is the one that stabilises the alloy against intergranular attack after elevated-temperature exposure.

Mechanical Properties

Property Value
Tensile strength 930 MPa (135,000 psi)
Yield strength, 0.2 % offset 517 MPa (75,000 psi)
Elongation, min in 50 mm 42.5 %

Elongation is what matters most for U-tube fabrication: a minimum of 42.5 % in 50 mm lets the bend be formed without cracking, and the low-carbon, niobium-stabilised chemistry keeps the bend region ductile after forming.

Size, Schedule and Finish Range

Item Range
Seamless tube outside diameter 4 – 219 mm
Seamless wall thickness 0.5 – 20 mm
Welded pipe outside diameter 5.0 – 1219.2 mm
Schedules SCH5, SCH10, SCH20, SCH30, SCH40, SCH60, SCH80, SCH120, SCH140, SCH160, XS, XXS
Lengths Single random, double random, cut length
Surface finish Annealed and pickled (AP), bright annealed (BA), NO.1, NO.4, 2B, HL, 8K, mirror
Forms Straight tube, U-bend, coiled, pancake coil, hydraulic tube
Ends Plain, beveled, threaded

Wire gauges from 10 SWG to 20 SWG are available for small-diameter instrument and sampling lines. Wall thickness tolerance, bend ovality and straight leg length are fixed at order entry because they control how the bundle fits the tubesheet.

Where Seamless U-Tubes Are Used

Heat exchangers and feedwater heaters – tubes handle high-temperature, high-chloride cooling water and process streams.

Chemical processing – thin-walled pressure vessels, process control equipment and high-pressure lines.

Offshore and marine – seawater-cooled equipment where pitting and crevice corrosion dominate.

Aerospace and pollution control – high-temperature ducting, scrubber and flue-gas hardware.

Frequently Asked Questions

Q: What is the difference between Grade 1 and Grade 2 in ASTM B444?
Grade 1 is supplied annealed for maximum formability, while Grade 2 is supplied solution treated for higher minimum strength. Both are the same UNS N06625 chemistry.

Q: What is UNS N06625 equivalent to in other systems?
It is listed as WERKSTOFF NR. 2.4856 in the DIN system and as NiCr22Mo9Nb in the EN system, with ASTM B444 and ASME SB444 as the usual product specifications.

Q: What maximum temperature can these tubes work at?
The alloy keeps useful strength and oxidation resistance up to about 816 °C (1520 °F); above that creep and oxidation rates rise and the design should be re-checked.

Q: Are the U-tubes seamless or welded?
ASTM B444 covers cold-worked seamless tube; welded pipe in the same alloy is bought to a separate specification. Heat exchanger U-bends are normally formed from seamless tube.

Q: What tests come with the tubes?
Mill certificates record chemistry, tensile, yield and elongation results, and finished tubes are checked for dimensions and surface and, where specified, for hydrostatic or eddy-current soundness.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry