Similar Outside, Very Different Inside
Seamless and welded pipe made from the C22 nickel alloy (UNS N06022) and pipe made from 316 stainless steel (UNS S31600) can look almost identical on a loading dock, yet the two behave completely differently once they are in service. C22 is a nickel-chromium-molybdenum-tungsten alloy in which nickel and the alloying elements make up more than half of the mass; 316 is an austenitic stainless steel that is roughly 70% iron and relies on about 17% chromium with 2.5% molybdenum for its corrosion resistance. The nickel alloy pipe is supplied to ASTM B622 for seamless pipe and tube and to ASTM B619 and B626 for welded pipe and tube, while 316 pipe is normally supplied to ASTM A312 and, on European projects, to EN 10216-5.
Price follows the chemistry, and C22 pipe costs several times more per kilogram than 316 pipe. The purpose of this comparison is to define exactly which service conditions justify the higher grade and which do not.
Chemistry and Product Standards
The two materials are separated by an order of magnitude in molybdenum content and by the presence of tungsten in the nickel alloy, which is what extends its resistance to localised corrosion.
| Element, % | C22 alloy pipe (UNS N06022) | 316 stainless pipe (UNS S31600) |
|---|---|---|
| Nickel | balance | 10.0–14.0 |
| Chromium | 20.0–22.5 | 16.0–18.0 |
| Molybdenum | 12.5–14.5 | 2.00–3.00 |
| Tungsten | 2.5–3.5 | - |
| Iron | 2.0–6.0 | balance |
| Carbon | 0.015 max | 0.08 max |
| Manganese | 0.50 max | 2.00 max |
| Silicon | 0.08 max | 0.75 max |
| Cobalt | 2.5 max | - |
| Vanadium | 0.35 max | - |
Applicable product standards:
C22 pipe: ASTM B622 (seamless pipe and tube), ASTM B619 (welded pipe), ASTM B626 (welded tube), with ASME equivalents used for pressure design.
316 pipe: ASTM A312 and A358 (seamless and welded austenitic pipe), ASTM A213 for heat exchanger tubing, EN 10216-5 and EN 10217-7 for European procurement.
Corrosion Performance in Chloride and Acid Service
Resistance to localised corrosion is commonly screened with the pitting resistance equivalent number, PREN = Cr + 3.3 (Mo + 0.5 W). Using typical mid-range compositions, C22 gives approximately 21 + 3.3 (13.5 + 1.5), or about 71, while 316 gives about 17 + 3.3 (2.5), or about 25. The practical meaning of that gap is a very large difference in the critical pitting and crevice corrosion temperatures measured in ferric chloride tests, and therefore in how much chloride the pipe can tolerate at temperature.
C22 pipe: handles wet chlorine, hypochlorite and chlorine dioxide bleach liquors, ferric and cupric chloride, mixed nitric-hydrofluoric pickling acid, contaminated sulfuric and phosphoric acids, and raw seawater. It is also highly resistant to chloride stress corrosion cracking.
316 pipe: is fully satisfactory in fresh water, mildly chlorinated water, food and pharmaceutical product contact, dilute oxidising acids, and atmospheric or mildly marine exposure. It is not suitable for concentrated chlorides at elevated temperature, where it pits and becomes liable to chloride stress corrosion cracking above roughly 60 °C.
The dividing line in practice is the chloride level combined with temperature and pH. Below the pitting resistance limit of 316, the stainless pipe is the economical and perfectly adequate choice. Where the chloride level is high, the pH is low, or oxidising species such as chlorine or ferric ions are present, the alloy pipe is the only reliable option.
Strength, Temperature and Pressure Design
ASTM B622 requires annealed C22 pipe to reach 690 MPa tensile strength, 283 MPa yield strength and 45% elongation. Type 316 pipe to ASTM A312 is specified at 515 MPa tensile and 205 MPa yield, with the low-carbon 316L variant at 485 MPa tensile and 170 MPa yield. Neither grade can be strengthened by heat treatment: 316 gains strength only through cold work and C22 only through cold reduction, so wall thickness rather than grade is normally the design lever when extra pressure capability is required.
At temperature the selection is driven by corrosion rather than by strength. Type 316 is restricted by sensitisation between about 425 and 815 °C and by a steady loss of allowable stress above roughly 550 °C. C22 retains useful strength over a similar band and, more importantly, continues to resist both oxidising and reducing acids at those temperatures, which is why it is common in flue gas desulphurisation and chemical process piping. Where a line is temperature-limited rather than corrosion-limited, a higher-chromium heat-resisting grade is normally evaluated instead, because at high temperature the life of both materials is governed by oxidation.
Fabrication, Welding and Availability
Type 316 pipe is welded with 316L or 308L-class electrodes and is among the most widely available pipe products in the world, stocked in every schedule and in sizes from small instrument tubing to large diameter transmission pipe. C22 pipe requires a matching nickel-chromium-molybdenum filler metal, lower heat input and clean, oxide-free joint faces, and its welds should be made with controlled interpass temperature to preserve corrosion resistance in the heat-affected zone.
Machining and forming follow the same pattern. Stainless pipe cuts, bends and machines with conventional tooling, whereas the nickel alloy work-hardens rapidly and demands rigid set-ups, sharp tooling and reduced surface speeds. Availability is the other practical factor: C22 is normally stocked in popular sizes, but larger outside diameters and heavy walls can carry extended lead times that must be planned into a project schedule.
Frequently Asked Questions
Q: Is C22 alloy pipe a type of stainless steel?
No. C22 is a nickel-based alloy with roughly 21% chromium, 13% molybdenum and 3% tungsten. Type 316 is an iron-based austenitic stainless steel, so the two are separate material families even though both are corrosion resistant.
Q: What is C22 pipe made of?
C22 pipe is made to the UNS N06022 composition: nickel as the balance, 20.0–22.5% chromium, 12.5–14.5% molybdenum, 2.5–3.5% tungsten, 2.0–6.0% iron, with very low carbon and silicon limits to protect weld corrosion resistance.
Q: Can C22 pipe be welded to 316 pipe?
Yes. A matching nickel-chromium-molybdenum filler metal is used for the joint, with low heat input and a controlled interpass temperature. The joint is established practice in chemical plants, but the design should account for the difference in thermal expansion between the two materials.
Q: Which pipe is stronger, C22 or 316?
Anneal-state C22 pipe has a higher specified yield strength, 283 MPa against 205 MPa for 316. The difference is modest, however, and in most projects the selection is decided by corrosion resistance rather than by strength.
Q: When is 316 pipe good enough?
Type 316 pipe is adequate whenever chlorides are low and temperatures are moderate, as in food, pharmaceutical, general chemical and architectural service. Once chlorides are combined with elevated temperature, low pH or oxidising species, the nickel alloy pipe becomes the reliable choice.
Q: What standard covers C22 pipe?
Seamless C22 pipe and tube are covered by ASTM B622, welded pipe by ASTM B619 and welded tube by ASTM B626. Plate, sheet and strip are covered by ASTM B575 and bar and rod by ASTM B574.





