What Is Oriented Silicon Steel?
Oriented silicon steel, also called electrical steel or transformer steel, is a ferrosilicon soft magnetic alloy with very low carbon content in which the crystal grains are deliberately aligned in one direction during processing so that the magnetic properties are optimised along the rolling direction. The silicon content of the family as a whole ranges from about 0.5 to 4.5 %, while grain-oriented grades normally contain around 3 % silicon. Adding silicon raises the resistivity and the maximum permeability of iron and lowers coercivity, core loss and magnetic ageing, which is precisely what a magnetic core needs.
Manufacturing Process
Commercial production of grain-oriented silicon steel began in the 1920s and has been refined continuously since. Modern production follows a fixed sequence.
Melting: high-purity iron is melted with controlled additions of silicon and aluminium to reach the target analysis and a low level of residual impurities.
Casting: the molten steel is continuously cast into slabs with a uniform structure.
Hot rolling: slabs are reheated and rolled to the required thickness, which already begins to align the grains in the rolling direction.
Cold rolling and annealing: further thickness reduction combined with heat treatment develops the cube-on-edge texture and relieves internal stress.
Insulating coating: a thin insulating layer is applied so that adjacent laminations in a stacked core cannot short circuit.
Final thickness of grain-oriented product is typically between 0.18 mm and 0.35 mm.
Why Core Loss and Permeability Matter
Core loss is the energy dissipated as heat when an alternating magnetic field passes through the material, and it is the property that most directly determines the efficiency of a transformer or a motor. Oriented silicon steel achieves low core loss by combining high resistivity with a well-aligned grain structure. High magnetic permeability is the second advantage: because the material conducts magnetic flux efficiently, a given power rating can be built into a smaller and lighter core. Reducing eddy current losses is the third, obtained by dividing the magnetic circuit into thin, individually insulated laminations.
Factors That Affect Performance
Silicon content: higher silicon raises resistivity and permeability and lowers core loss, but reduces ductility, which is why grain-oriented grades settle at around 3 % silicon.
Grain orientation: the sharper the alignment, the lower the loss and the higher the permeability along the rolling direction.
Thickness: thinner laminations cut eddy current loss but increase the number of cuts and the stacking cost.
Coating quality: coating thickness and adhesion determine insulation resistance and punchability as well as loss behaviour.
Stress and handling: bending, shearing and stacking introduce residual stress that raises core loss, so stress relief annealing is applied to wound cores.
Cost: high-permeability grades carry a price premium that has to be justified by lower total transformer losses and reduced weight.
Typical Grades and Applications
Grain-oriented grades are normally designated by nominal thickness in millimetres followed by a code and the guaranteed maximum core loss measured at 1.7 T and 50 Hz, for example 23Q110, 27Q120 and 30Q130 under GB/T 2521.1, or by the M-series grades of ASTM A876. Minimum magnetic induction at 800 A/m is generally about 1.88 T for conventional grades and 1.92 T or higher for high-permeability grades.
| Typical grade | Nominal thickness | Maximum core loss at 1.7 T, 50 Hz |
|---|---|---|
| 23Q110 | 0.23 mm | 1.10 W/kg |
| 27Q120 | 0.27 mm | 1.20 W/kg |
| 30Q130 | 0.30 mm | 1.30 W/kg |
| 27QG095, high permeability | 0.27 mm | 0.95 W/kg |
Power transformers, distribution transformers, instrument transformers, electric motors, generators, inductors and magnetic sensors all depend on this material. Large power transformers use the lowest-loss grades available, distribution transformers balance loss against first cost, and small motors and sensors are more often wound from thinner high-permeability strip.
FAQ
Q: What is the difference between oriented and non-oriented silicon steel?
Oriented grades have a strongly aligned grain structure and give very low loss in the rolling direction, while non-oriented grades have randomised grains and are used where flux flows in several directions, such as motor stators.
Q: How much silicon does oriented silicon steel contain?
Electrical steels as a family span about 0.5 to 4.5 % silicon, and grain-oriented transformer grades are usually produced at around 3 % silicon.
Q: Why are laminations made so thin?
Eddy current loss falls as thickness is reduced, so 0.23 mm to 0.30 mm strip is standard for transformers. Thinner material also costs more to shear and stack, so the optimum is a balance.
Q: Does handling really affect core loss?
Yes. Bending, shearing and careless stacking introduce residual stress and raise loss measurably, which is why wound cores are stress relief annealed after forming.
Q: Which grades suit large power transformers?
Low-loss high-permeability grades in 0.23 mm to 0.27 mm thickness, where the reduction in no-load loss over the life of the transformer justifies the higher strip price.





