May 27, 2025 Leave a message

Is Alloy K500 Magnetic? Magnetism, Surface Films and Strength

Short Answer: Alloy K500 Is Non-Magnetic

In the annealed and precipitation-hardened conditions, Alloy K500 is essentially non-magnetic. It is a paramagnetic material with very low magnetic permeability, and it stays that way down to about -120 °C. That behaviour, combined with high strength and excellent corrosion resistance, is why the grade is selected for instrumentation housings, compass components, gyroscope parts and other assemblies where a magnetic signature would disturb the working of the device.

The practical qualification is that the alloy is non-magnetic as supplied, but it is not immune to becoming locally magnetic in service. Two mechanisms are responsible: a surface film formed during hot processing, and cold work introduced during forming or machining.

Why a Magnetic Layer Can Form on the Surface

Alloy K500 gains its strength from aluminium and titanium additions. When the material is heated for hot working, annealing or ageing, aluminium and copper are selectively oxidised at the surface. The elements that leave the surface layer are the same ones that keep the alloy non-magnetic, so the remaining skin becomes nickel-rich and shows a measurable magnetic response even though the bulk of the section is unaffected.

The layer is shallow and can be removed by pickling or by an acid light dip. After descaling, the surface restores the non-magnetic behaviour of the base material. Where magnetic permeability is a functional requirement, such as a sensor housing or a navigation component, the specified surface treatment must therefore be verified by measurement on the finished part rather than assumed from the mill certificate.

Cold Work, Permeability and Temperature Effects

Cold working raises dislocation density and can lift permeability slightly, particularly in heavily formed sections such as rolled threads, swaged ends and tight bends. The effect is small compared with that of a nickel-rich surface film, but it is measurable, and highly cold-formed parts should be assessed in the as-delivered condition.

The magnetic transformation of the nickel-copper system lies well below ambient temperature. The alloy remains non-magnetic at temperatures as low as -120 °C, which covers most cryogenic instrumentation service, and no magnetic transition occurs in normal industrial or offshore operating ranges.

Strength Advantage Over Alloy 400

Alloy K500 is a precipitation-hardenable nickel-copper alloy that offers corrosion resistance slightly better than Alloy 400 while adding a large gain in mechanical properties. In the age-hardened condition its yield strength is approximately three times that of Alloy 400 and its tensile strength is roughly twice as high. The alloy can be further strengthened by cold working before the precipitation treatment, and it can also be supplied in the cold-worked and aged condition for the highest strength levels.

One trade-off must be recorded: in the age-hardened state, Alloy K500 is more susceptible to stress corrosion cracking than Alloy 400 in certain environments. Because the strengthening comes from gamma-prime precipitates, long-term elevated-temperature service is normally controlled to avoid over-ageing and the associated loss of strength.

Forms, Sizes and Typical Applications

Product form Size range from Size range to
Pipe 0.5 in 8 in
Tube 12 mm 260 mm
Pipe fittings 0.5 in 8 in
Flanges 0.5 in 8 in
Round bar 3 mm 800 mm

Offshore engineering takes advantage of both the corrosion resistance and the low permeability, using the alloy for valve stems, pump shafts and components exposed to seawater, as well as for magnetic housings in compasses and navigation systems. Chemical processing uses it for heat exchangers, evaporators and pressure vessels where the process stream is acidic or alkaline and mechanical loading is severe. Oil and gas production applies it to pipe, valves and instrumentation parts in corrosive wells. Aerospace relies on it for fasteners and springs that must combine strength with corrosion resistance, and medical device makers use it for pacemaker components because the material is non-magnetic and biocompatible.

Fabrication and Heat Treatment

The alloy is ductile and can be joined by welding, brazing and soldering, but care is needed to avoid intergranular corrosion. Exposure to temperatures between about 425 °C and 870 °C (800 °F to 1600 °F) can sensitise the material, so an anneal after welding, brazing or soldering is recommended. Cold forming by rolling, bending and stamping is practical when the work is done in stages with intermediate anneals to reduce the risk of cracking.

Precipitation hardening is carried out in two steps. Solution annealing brings the material to a temperature between 925 °C and 1040 °C (1700 °F to 1900 °F), holds it there, and then cools it at a controlled rate to dissolve precipitates formed during earlier cold work. The subsequent ageing treatment at about 480 °C to 565 °C (900 °F to 1050 °F) forms the fine gamma-prime particles that deliver the strength and hardness. Time and temperature in the ageing step are selected to reach the required property combination.

Frequently Asked Questions

Q: Is Alloy K500 magnetic?
No. In the annealed and aged conditions it is essentially non-magnetic with very low permeability, and it remains non-magnetic at temperatures as low as -120 °C.

Q: Why did a machined part show magnetic attraction?
A nickel-rich magnetic film can form on the surface during heating, because aluminium and copper are selectively oxidised and leave the skin enriched in nickel. Pickling or an acid light dip removes the layer.

Q: Does cold working affect magnetic permeability?
Heavily cold-formed areas such as swaged ends and rolled threads can show slightly higher permeability than the parent material, although the change is far smaller than that caused by a surface film.

Q: How much stronger is Alloy K500 than Alloy 400?
The age-hardened yield strength is roughly three times that of Alloy 400 and the tensile strength about twice, reached through aluminium and titanium additions plus a precipitation treatment.

Q: What temperature range should be avoided during fabrication?
Exposure between about 425 °C and 870 °C (800 °F to 1600 °F) can cause intergranular corrosion, so welded or brazed assemblies should be annealed after joining.

Q: Where is a non-magnetic high-strength alloy needed?
Typical duties include instrumentation components, magnetic housings for compasses and navigation equipment, gyroscope parts and medical devices such as pacemaker components.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry