Mar 14, 2024 Leave a message

UNS N07725 Precipitation-Hardening Nickel Alloy for High-Performance Service

Overview of UNS N07725

UNS N07725 is a precipitation-hardening nickel-chromium-molybdenum alloy developed for high-strength service in oilfield, marine, aerospace and chemical process environments. Its base chemistry follows the solid-solution Ni-Cr-Mo grade UNS N06625, but titanium and niobium additions make the alloy responsive to an aging treatment rather than to cold work. The result is roughly double the yield strength of the solid-solution grade, with high ductility retained.

Because the strength is developed by heat treatment, heavy sections can be supplied at high strength without the residual stresses and section-size limits of cold-worked products. Aged bar and forgings are therefore standard for fasteners, control shafts and pressure-containing parts that must resist both mechanical load and chloride-bearing media.

Chemical Composition of UNS N07725

Element (wt.%) UNS N07725 UNS N06625 (reference)
Nickel, Ni 55.0 - 59.0 58.0 min
Chromium, Cr 19.0 - 22.5 20.0 - 23.0
Molybdenum, Mo 7.0 - 9.5 8.0 - 10.0
Niobium + Tantalum 2.75 - 4.00 3.15 - 4.15
Titanium, Ti 1.00 - 1.70 0.40 max
Aluminium, Al 0.35 max 0.40 max
Iron, Fe Balance 5.00 max
Carbon, C 0.03 max 0.10 max
Manganese, Mn 0.35 max 0.50 max
Silicon, Si 0.20 max 0.50 max
Sulphur, S 0.010 max 0.015 max

Titanium and niobium are the deliberate difference from UNS N06625: with a small aluminium addition they form the fine precipitate dispersion that carries the strength, while chromium and molybdenum remain high enough to preserve corrosion resistance. Carbon is kept low to limit carbide precipitation during welding and high-temperature exposure.

Mechanical Behaviour and Heat Treatment

Parts are supplied solution annealed, or solution annealed and aged. Aging is carried out in the approximate range of 620 to 760 degrees C, where gamma-double-prime and gamma-prime precipitates lock the structure in place. The key features are:

High yield strength: the aged condition provides about twice the yield strength of solid-solution UNS N06625 in comparable product forms.

Ductility retained: hardening by heat treatment instead of cold reduction keeps elongation and notch toughness suitable for impact-loaded subsea hardware.

PREN above 45: the combined chromium, molybdenum and niobium content places the alloy well above conventional stainless steels in chloride pitting resistance.

Stable microstructure: prolonged exposure at elevated service temperature does not cause rapid over-aging or embrittlement.

Fabrication: welding, machining and forming are done in the solution-annealed condition, with aging applied afterwards where full strength is required.

Corrosion Resistance and Sour Service

The alloy was designed for environments where chlorides, hydrogen sulphide and carbon dioxide occur together at elevated pressure and temperature, conditions that rule out conventional low-alloy and martensitic steels. A pitting resistance equivalent number above 45 gives strong resistance to pitting and crevice corrosion in aerated seawater and chloride-rich process streams, together with resistance to chloride stress corrosion cracking and general corrosion in many reducing and oxidising media.

Sour oil and gas selection is governed by NACE MR0175 / ISO 15156-3, which lists precipitation-hardening nickel alloys for use under specified hydrogen sulphide, carbon dioxide and chloride partial pressures with mandatory hardness and heat-treatment controls. UNS N07725 is applied in pipe hangers, mandrels, valve bodies and vessels, most of them forged rather than machined from bar stock.

Compared with the precipitation-hardening nickel-copper grade UNS N05500, long used in marine construction, the higher chromium and molybdenum content removes the vulnerability to hydrogen embrittlement seen when that older grade is combined with less noble steels under cathodic protection. This is why UNS N07725 is now selected for subsea control shafts and exposed structural elements.

Product Forms and Applications

Bar stock is produced in diameters from 1 in (25.4 mm) to 4 in (101.6 mm), with larger diameters and forged shapes to order, in solution-annealed, aged, cold-drawn, peeled or ground-polished condition.

Oilfield equipment: pipe hangers, mandrels, wellhead and downhole hardware, valves and pressure vessels for sour service.

Marine systems: control shafts, fasteners and structural components exposed to seawater.

Aerospace and gas turbines: high-strength fasteners and hardware requiring strength retention at elevated temperature.

Pollution control and chemical processing: scrubber, incinerator and reactor components handling chloride-bearing media.

Fastener stock: small diameters for bolts and studs, larger sizes for mating nuts and complementary hardware.

Frequently Asked Questions

Q: What makes UNS N07725 stronger than UNS N06625?
Both share a similar nickel-chromium-molybdenum base, but UNS N07725 contains titanium and niobium that form a fine precipitate dispersion during aging, so the aged condition reaches about twice the yield strength of the solid-solution grade while remaining ductile.

Q: Is UNS N07725 suitable for sour gas wells?
Yes. It is widely used for sour-service mandrels, pipe hangers and valve bodies, provided the finished part meets the hardness and heat-treatment requirements of NACE MR0175 / ISO 15156-3 for the well conditions concerned.

Q: Can UNS N07725 be welded?
It is weldable, and welding is normally performed in the solution-annealed condition. Where full aged strength is required, aging is carried out after welding, using matching nickel-base filler material to retain corrosion resistance.

Q: How does it compare with UNS N05500?
The nickel-copper grade UNS N05500 has served marine hardware for decades, but it resists pitting less well and is more sensitive to hydrogen embrittlement. UNS N07725 gives higher strength, better chloride corrosion resistance and improved toughness under cathodic protection.

Q: What forms and sizes are available?
Bar from 1 in (25.4 mm) to 4 in (101.6 mm) diameter is normally held in solution-annealed or aged condition, with larger diameters, cold-drawn sizes and forged components produced to order.

Q: Which environments should be avoided?
Hot oxidising acids and sustained exposure above the alloy's aging-stability temperature are not recommended, because the precipitate structure can over-age and lose strength. Oxidising acid duty is better reviewed against a higher-molybdenum grade such as UNS N06022.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry