Dec 15, 2023 Leave a message

Comparison between MonelK500 and Monel400

Comparison between MonelK500 and Monel400

 

The composition of Monel K500 and Monel 400 differs very little, so their corrosion resistance is equivalent. However, Alloy K500 has several times the yield strength and tensile strength, making it more suitable for heavy-duty applications.

Originally developed by International Nickel in the early 20th century, Monel® 400 is one of a series of products subsequently developed based on the proportions of nickel and copper in ores found naturally in Canadian mines. Since the ore is typically a very stable component, an equally stable, corrosion-resistant alloy can be obtained using this method. The Monel® trademark, now owned by Specialty Metals, has become synonymous with this family of alloys, although it is now widely produced by many factories.

Monel400 is composed almost entirely of nickel (>63%) and copper (28-34%), with only smaller amounts of iron, manganese and other trace elements. Nickel and copper are soluble in each other, so the microstructure consists of a single phase. It can be strengthened by cold working but not by heat treatment. Alloy 400 has relatively high strength compared to other copper alloys, and its impact properties remain at levels below zero to 480°C.

Comparison between MonelK500 and Monel400

Comparison between MonelK500 and Monel400

Monel400 chemical composition:

Element content%

Nickel (plus cobalt): ≤63.0

Aluminum: ≤0.50

Carbon: ≤0.15

Copper: 28.0 -34.0

Iron: 1.00-2.50

Manganese: ≤2.0

Sulfur: ≤0.02

Silicon: ≤0.5

Titanium: ≤0.30

Due to its composition being almost entirely nickel and copper, Monel 400 is particularly resistant to seawater corrosion and will quickly form a complex yet thin and sticky protective surface film when exposed to clean seawater. This protective film protects the alloy in most cases, but the only drawback is that the flow rate is very slow and can form fouling that can lead to pitting or certain contaminants that can damage the film.

Like seawater, Monel 400 is also resistant to corrosion by other chloride solutions and a range of acids, including chlorine. As long as the oxygen content in the solution is minimal, that is, under reducing conditions, it is resistant to hydrofluoric acid and hydrochloric acid. It is widely used in marine and chemical industries mainly due to its excellent corrosion resistance.

However, the strength level of Monel400 limits its use in more structural applications. Monel K500 was developed to overcome this limitation. Its composition is the same as Monel400, but aluminum and titanium are added in small amounts (3-4% total). Aluminum and titanium combine to form microscopic precipitates that can be controlled by heat treatment. After forging or rolling, round steel undergoes an aging heat treatment, keeping it at high temperature for several hours and then slowly cooling in the air. This process ensures that as much aluminum and titanium as possible can be extracted from the solution and form a fine, widely dispersed network. These precipitates produced significant improvements in mechanical properties - a 4-fold increase in yield strength and a 2-fold increase in tensile strength. The increased strength of Monel K500 means it can be used effectively on more challenging components such as marine shafts, valve stems, fasteners, mixer and stirrer shafts as well as doctor blades, drill collars and heat exchanger components.

MonelK500 chemical composition

Element content%

Nickel (plus cobalt): ≥63.0

Carbon: ≤0.25

Manganese: ≤1.5

Iron: ≤2.0

Sulfur: ≤ 0.01

Silicon: ≤0.5

Copper: 27.0 -33.0

Aluminum: 2.30 - 3.15

Titanium: 0.35 - 0.85

Since the composition of Monel K500 is virtually identical to that of Monel 400, the basic chemical and corrosion resistance remains the same. There is an argument that Alloy K500 may be more susceptible to stress corrosion cracking in limited circumstances, but this is most likely due to its use in higher stress applications (because of its higher strength).

Since the specifications of Monel K500 have no obvious shortcomings compared to Monel400, and with the significant improvement in strength, a large number of new application fields have been opened up, so the market usage of Monel K500 materials is more abundant.

 

Send Inquiry

whatsapp

Phone

E-mail

Inquiry