AMS 5540 Inconel 600 UNS N06600 Aerospace Annealed Sheet
video

AMS 5540 Inconel 600 UNS N06600 Aerospace Annealed Sheet

AMS 5540 Inconel 600 UNS N06600 aerospace annealed sheet is a nickel‑chromium‑iron alloy plate produced to aerospace‑grade specifications. It is supplied in the annealed condition to deliver balanced ductility and stable mechanical properties. This alloy resists high‑temperature oxidation and...
Send Inquiry
Chat Now

As a leading supplier and manufacturer in China, GNEE Steel provides cost-effective nickel-based alloy products.

Product Introduction

Gnee Super Alloy (Tianjin) Co., Ltd. is one of the most professional manufacturers and suppliers of ams 5540 inconel 600 uns n06600 aerospace annealed sheet in China. If you're going to wholesale high quality ams 5540 inconel 600 uns n06600 aerospace annealed sheet made in China, welcome to get free sample from our factory. Good service and reasonable price are available.

 

AMS 5540 Inconel 600 UNS N06600 aerospace annealed sheet is a nickel‑chromium‑iron alloy plate produced to aerospace‑grade specifications. It is supplied in the annealed condition to deliver balanced ductility and stable mechanical properties. This alloy resists high‑temperature oxidation and stress corrosion cracking, maintaining reliable performance under cyclic thermal loads.

 

It undergoes strict PMI, dimensional inspection and surface examination to satisfy aerospace traceability and acceptance rules. Typical uses include aircraft exhaust components, heating ducts and engine auxiliary structures, where consistent metallurgy and forming capability are required for high‑temperature service.

Request a Quote

 

Inconel 600 Sheet - AMS 5540 - UNS N06600 Alloy
Nickel Alloy 600/ Inconel 600 (UNS N06600)
Inconel 600 Sheet - AMS 5540 - UNS N06600 Alloy
Nickel Alloy 600/ Inconel 600 (UNS N06600)
 

Chemical Composition of AMS 5540 Nickel 600

 

This chemical range complies strictly with AMS 5540 aerospace specification for annealed Inconel 600 sheet. Every batch is verified by PMI test to eliminate material mixing and meet aerospace traceability requirements.

 

Element Content (wt.%)
Ni (Nickel) ≥72.0
Cr (Chromium) 14.0 – 17.0
Fe (Iron) 6.0 – 10.0
C (Carbon) ≤0.15
Mn (Manganese) ≤1.00
Si (Silicon) ≤0.50
S (Sulfur) ≤0.015
Cu (Copper) ≤0.50

 

Mechanical Properties of AMS 5540 Inconel 600

 

These mechanical limits apply to annealed AMS 5540 Inconel 600 aerospace sheet. Each heat lot is sampled and tested to confirm compliance, supporting forming and high‑temperature service for aviation components.

 

Property Requirement
Tensile Strength, Rm 550 MPa (80 ksi) min
Yield Strength, Rp0.2 240 MPa (35 ksi) min
Elongation (50 mm / 2 in gauge) 30 % min
Hardness, HB ≤187 HB

Note: Room temperature, longitudinal direction; values represent minimum requirements

 

Heat Treatment Properties of Inconel 600 Aerospace sheet (AMS 5540)

 

Applicable to annealed UNS N06600 sheet for aerospace service

Item Details
Standard delivery condition Full annealed, the required state for AMS 5540 aerospace sheet
Annealing temperature range 980 ℃ – 1040 ℃, hold for proper soaking time
Cooling method Air cool or water quench to retain uniform austenitic grain structure
Core function of annealing Dissolve carbide precipitates, reduce residual stress, maximize ductility for forming
Age hardening response Non-age-hardenable; strength cannot be improved by aging treatment
Stress relief treatment 870–900 ℃, slow cooling, used after bending, stamping or forming operations
Grain structure after full anneal Uniform equiaxed austenite, stable under cyclic high-temperature exposure

 

AMS 5540 specifies full annealed supply condition. Avoid overheating above 1040 ℃ to prevent excessive grain coarsening, which reduces ductility and fatigue resistance for aerospace parts.

 

Surface Finishing Process for UNS N06600 Aerospace sheet

 

Item Details
Pickling & passivation Acid pickling removes oxide scale after heat treatment; passivation forms stable Cr₂O₃ film
Bright annealing In protective atmosphere, oxide-free bright surface, no subsequent pickling required
Sand blasting Fine glass bead blasting, uniform matte surface, removes surface defects
Polishing Mechanical polishing to Ra 0.4–1.6 μm, for high-purity / nuclear heat exchanger tubing

 

AMS 5540 Aerospace Annealed Sheet Tolerances

 

Note: SAE AMS 5540 references AS4194 for dimensional tolerances, for UNS N06600 Inconel 600 annealed aerospace sheet, max nominal thickness 50.8 mm (2 in)

 

Tolerance Item Nominal Size Range Permissible Tolerance
Sheet Thickness ≤ 0.40 mm ±0.03 mm
Sheet Thickness >0.40 ~ 1.60 mm ±0.05 mm
Sheet Thickness >1.60 ~ 6.35 mm ±0.08 mm
Sheet Thickness >6.35 ~ 50.80 mm ±0.13 mm
Width ≤ 1220 mm 0 / +1.6 mm
Width >1220 mm 0 / +3.2 mm
Length ≤ 2440 mm 0 / +3.2 mm
Length >2440 mm 0 / +6.4 mm
Flatness All sheet gauges Max 6 mm deviation per 1000 mm span
Edge Cut Sheared / machined edge ±0.8 mm

 

AMS 5540 itself does not fully list all dimensional limits; tolerance rules follow AS4194 aerospace flat product specification. All sheets are inspected dimensionally before release to satisfy aerospace traceability requirements.

 

Advantages of Inconel 600 for Aerospace

 

 

High-Temperature Oxidation Resistance

It maintains a continuous protective Cr₂O₃ oxide layer up to 600 ℃, with oxidation rate below 0.1 mm per 1000 h, resisting scaling for exhaust ducts and heating components.

Stable Mechanical Performance at Elevated Temperature

At 538 ℃, the alloy retains minimum tensile strength of 480 MPa. Its annealed structure avoids rapid strength drop under cyclic thermal load in airborne service.

Stress Corrosion Cracking Resistance

In chloride and humid high-temperature environments, it shows far lower crack growth rate than 321 stainless steel, reducing failure risk for pressurized aerospace auxiliary structures.

Excellent Formability for Complex Parts

Annealed AMS 5540 sheet delivers minimum 30% elongation. It supports deep drawing and bending without cracking to fabricate irregular aircraft thermal components.

 

Typical Applications of Alloy 600 Aerospace sheet

 

AMS 5540 Sheet and Plate

Aircraft Exhaust System Components

 

Used for exhaust ducts and shrouds enduring cyclic temperature up to 600 ℃. Its low oxidation rate below 0.1 mm/1000 h prevents scale spalling under repeated thermal cycling.

Aircraft Heating & Environmental Ducting

 

Fabricated into cabin heating ducts, working steadily within 200–500 ℃. It resists stress corrosion from humid air and chloride contaminants inside the ventilation loop.
AMS 5540 Inconel 600 Sheet: High-Temperature Aerospace Solutions

 

Inconel 600 Nickel Alloy (UNS N06600)

Auxiliary Engine Thermal Shield Parts

 

Serves as heat shields for APU assemblies. The material retains tensile strength above 480 MPa at 538 ℃ to isolate high heat and protect adjacent aircraft wiring.

Aerospace Ground Support Thermal Hardware

 

Applied to high-temperature test fixtures and heating chambers. It maintains stable grain structure after hundreds of heating cycles for repeated aerospace component qualification tests.

AMS 5540 Inconel 600 Sheet: High-Temperature Aerospace Solutions

 

Why Choose GNEE STEEL as Your Supplier of Nickel Alloy Seamless Tubes?

 

Standard compliance:

Our nickel alloy seamless tubes comply with ASME B167, RCC-M and other applicable nuclear-grade specifications. Each batch is produced, inspected and documented following the designated code requirements to satisfy nuclear project qualification rules.

 

Tight chemical control:

We implement strict melting and analysis control for chemical composition. Trace impurities and cobalt content are limited to ultra-low levels, which reduces activation risk and meets nuclear radiation service requirements.

 

Full non-destructive testing:

Every tube undergoes 100% eddy current testing plus ultrasonic inspection. The acceptance threshold for internal and surface defects is set to stringent nuclear-grade limits to avoid hidden service failures.

 

Individual hydrostatic test:

Each seamless tube is subjected to a separate hydrostatic test at the specified pressure. We record test pressure, holding time and visual check results to verify reliable pressure-bearing performance.

 

Nickel Alloys | Inconel 600 | AMS 5540
hydrostatic test
Inconel® 600 Strip Coil Foil | ASTM B168 | AMS 5540
eddy current testing
Inconel® 600 Strip Coil Foil | ASTM B168 | AMS 5540
PMI test
INCONEL 600, Annealed, Material Data Sheet
ultrasonic inspection

 

Get MTC for Nickel 600 seamless tube/pipe

 

 

Packaging and Shipping

 

 

  

Nickel Inconel 600 AMS 5540

  

Alloy 600 Sheet, AMS 5540

 

 

Hot Tags: ams 5540 inconel 600 uns n06600 aerospace annealed sheet, China ams 5540 inconel 600 uns n06600 aerospace annealed sheet suppliers, Inconel 600 Plate, inconel alloy cooling system parts, inconel alloy extrusion molding process, inconel alloy piston parts, inconel alloy resistor parts, Inconel UNS N06625 Pipe

Send Inquiry

whatsapp

Phone

E-mail

Inquiry